Browse all practice questions for the Installer Technician Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Installer Technician Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • What is the sum of (20) + (-25) + (42)?
  • What is a common characteristic of direct current compared to alternating current?
  • What is the primary reason Series 59 coaxial cable is no longer used?
  • What is the recording head of a tape recorder actually considered to be?
  • What type of fiber-optic attenuator allows for the adjustment of loss in either stepped or continuous movements?
  • Which formula is used to calculate electrical power?
  • What does regular signal leakage monitoring help to minimize?
  • According to the left-hand rule for electromagnetism, where should your thumb point?
  • What is the purpose of the first equalizer in the line extender?
  • In what unit is electrical resistance measured?
  • How is actual insertion loss on a two-way splitter calculated?
  • What is a respectful way to treat a customer's property during a service visit?
  • Which situation indicates that a directional coupler is correctly wired in a loop-through system?
  • What can excessive current flow cause in a conductor?
  • What standard is applied in all modern Ethernet data cables, jacks, and connectors?
  • During the six-step troubleshooting process, what step involves determining whether a problem is intermittent or constant?
  • What type of reasoning involves applying a general statement to a new situation?
  • What is the purpose of voltage drops in a DC series circuit?
  • What is the insertion loss result when using an optical coupler with a desired split ratio of 40/60?
  • What test equipment identifies specific wiring problems on four-pair UTP/STP patch cords?
  • How is 0.893 volts expressed in power of 10 and metric prefix form?
  • If there is no signal on the input cable of the second directional coupler in a loop-through drop system, what is the likely problem?
  • What is the effect of non-verbal communication in customer service?
  • Why is it important to take notes and accurately record data at each job location?
  • What is a benefit of regular signal leakage monitoring and repair aside from FCC compliance?
  • A signal increase of 1 dB represents approximately what percentage increase in power?
  • A decrease of 1 millivolt (mV) at a signal level of 40 dBmV is approximately equivalent to a decrease of how many dB?
  • How is a symbol used in schematic circuit diagrams?
  • In an electrical circuit, what does the conductor specifically provide?
  • What is the total current IT in a DC series circuit with R1 = 10 ohms, R2 = 20 ohms, R3 = 30 ohms, R4 = 40 ohms, and a total voltage ET = 50 V?
  • What happens to the current if the resistance is increased while the voltage remains constant?
  • What is the result of squaring the number 7?
  • What is the total voltage in a DC series circuit with ER1 = 20V, ER2 = 45V, and ER3 = 57V?
  • How is 0.00004 expressed in scientific notation?
  • How is total resistance calculated in a DC series circuit?
  • What do flux lines do around a magnet?
  • What are the FCC requirements regarding leakage monitoring?
  • What does active listening involve?
  • What is the result of dividing (480 x 10^-5) by (60 x 10^-3)?
  • Which part of the circuit is responsible for current flow back to the power source?
  • What does the axiom state about quantities that are equal to the same quantity?
  • How do you calculate the missing resistor R2 in a DC series circuit with R1 = 33 ohms, R3 = 47 ohms, R4 = 56 ohms, and a total resistance RT = 197 ohms?
  • How are communication soft skills connected to customer satisfaction?
  • What does voltage measure in an electrical circuit?
  • Which resistor experiences the greatest voltage drop in a DC series circuit with R1 = 25 ohms, R2 = 50 ohms, R3 = 75 ohms, and R4 = 10 ohms?
  • Which exemption does the FCC allow for cable networks with less than 1,000 customers regarding proof-of-performance (POP) testing?
  • What factor primarily determines whether an element is a conductor, semiconductor, or insulator?
  • How is 5 kilovolts expressed in standard form?
  • A light bulb consumes 60 watts of power with 0.9 amperes of current. What is the bulb's resistance?
  • What happens if there is a bad connection at the input port of a drop splitter?
  • Which amplifier is best suited for resolving issues with a digital STB or cable modem due to long cable runs?
  • What is the most likely cause of reduced signal quality in fiber-optic transmission?
  • What stance represents a neutral, open position during a customer conversation?
  • What does the filing of forms and reports in a cable operator's public file indicate?
  • What component is responsible for distributing amplified forward RF signals from the amplifier module?
  • How much power is consumed in a DC series circuit with R1 = 50 ohms, R2 = 100 ohms, R3 = 183.33 ohms, IT = 0.6 amperes, and ET = 200 volts?
  • What is an RJ45?
  • What should be verified when connecting a device to the correct AC to DC power supply?
  • What is the primary function of an optical power meter (OPM)?
  • What type of connection is typically used for the AC input voltage in a line extender amplifier?
  • What is operational gain in terms of signal processing?
  • After restoring a customer's service, how should you communicate the resolution?
  • Which test equipment is used to measure cable lengths and locate faults?
  • What is the equivalent of 20 milliamperes in amperes?
  • For 2 bels of similar impedance cable, what is the input-to-output power ratio?
  • What is the result of 0.5349 divided by 0.1420?
  • What is the primary use of loose-tube fiber-optic cable?
  • Which statement best describes creative problem solving?
  • What type of signal is received by the input port of a line extender housing?
  • What characteristic is typical of a semiconductor material?
  • If the output of a line extender is 3 dB lower than it normally should be, what does this imply?
  • What would happen if one resistor fails open in a DC series circuit?
  • What is the required resistance for a circuit with an applied voltage of 30 volts and a current of 1.3 amperes?
  • What causes electric current to be produced in a circuit?
  • Which of the following describes total resistance in a series circuit?
  • What is impulse noise primarily caused by?
  • Where does frequency-dependent attenuation begin in the forward signal path of the line extender?
  • What is the total resistance in a DC series circuit with resistances 15 kilohms, 25 kilohms, and 47 kilohms?
  • What does the ampere measure in electrical circuits?
  • What is the primary purpose of a tagger when measuring signal leakage?
  • What does a negative value expressed in dBmV indicate?
  • What is the result of 7 3/8 divided by 7 1/4?
  • What additional requirement is imposed on cable operators regarding Equal Employment Opportunity (EEO) under the Cable Communications Policy Act?
  • If the current in a circuit is 0.8 amperes and the resistance is 100 ohms, what is the voltage?
  • What is the relationship between voltage, current, and resistance known as?
  • What is the product of 4/7 x 9 4/11?
  • What role does empathy play in customer interactions?
  • A fraction compares which two amounts?
  • What happens between magnetic poles that are alike?
  • How is stereotyped thinking best described?
  • Which type of interference is often a consequence of poor shielding in STBs?
  • What is the power ratio corresponding to a 2 dB attenuation?
  • What does ingress typically refer to in the context of telecommunications?
  • What options does an over-the-air (OTA) broadcast station have for carriage on a cable operator's network?
  • In signal processing, what does 'tilt' refer to?
  • An input-to-output power ratio of 10:1 corresponds to which input-to-output voltage ratio?
  • What occurs to the resistance of a material with a negative temperature coefficient as the temperature increases?
  • What happens to resistance when the cross-sectional area of a conductor decreases?
  • What is the sum of 3 6/9 + 6 1/3 + 9 5/9?
  • How does temperature usually affect the resistance of materials with a negative temperature coefficient?
  • Why do dBmV values progress in a nonlinear fashion compared to a linear millivolt scale?
  • When is it appropriate to replace the drop cable between the ground block and the customer's tap?
  • Which cabling method can an installer use to control resistance at customer premises?
  • What type of loss occurs when the bend radius of a fiber-optic line decreases?
  • How far must an aerial drop cable be placed from the power utility feed?
  • In a DC series circuit with resistors R1 = 10 ohms, R2 = 15 ohms, R3 = 20 ohms, and R4 = 5 ohms, how does the current compare across the resistors?
  • Which component is crucial for ensuring minimal signal disturbance in a drop splitter setup?
  • What is the recommended tool for tightening F-connectors during ingress checks?
  • What does being "active" as a critical thinker entail?
  • What is the expected outcome when a drop splitter is incorrectly connected?
  • In the acronym RESPECT, what does the "S" stand for?
  • In a DC series circuit, how is total resistance calculated?
  • Which of the following is a common source of over-the-air ingress?
  • What signal level indicates a poor connection at the splitter’s output ports?
  • How can a technician demonstrate professionalism during a service call?
  • In a drop splitter configuration, what would indicate a need for replacement of equipment?
  • If R = 40 ohms and E = 120 V in a DC series circuit, what is the circuit current?
  • What is one justification for implementing state-issued franchises over local franchises?
  • What characterizes direct current (DC)?
  • What does a circuit load accomplish?
  • Which orbital shell has a maximum capacity of 18 electrons?
  • What issue can poorly shielded set-top boxes (STBs) cause?
  • What do signal level controls in an amplifier adjust for?
  • If a fault is affecting the whole house, where should you begin your isolation?
  • What unit of measure is used to quantify the field strength of electromagnetic radiation?
  • When the length of a conductor increases, how does this affect its resistance?
  • How to calculate the average of the numbers 2, 3, 7, 8?
  • What non-verbal sign might indicate that the customer is happy?
  • When locating a live cable, what is the next step after placing the coupler around it?
  • What is the result of 13 x 0.123?
  • What is the result of (250 x 10^-6) - (7 x 10^-5)?
  • What is typically affected when measuring inadequate port-to-port isolation in a drop splitter?
  • What type of practices must cable operators hold according to the Cable Communications Policy Act of 1984?
  • Why is maintaining a clear tone of voice important in customer service?
  • When the cross-sectional area of a conductor doubles, what happens to its resistance?
  • What is the input-to-output power ratio of a coaxial cable with 1 dB of attenuation?
  • What is a common cause of common path distortion (CPD) at the ground block?
  • What is the primary function of a franchise authority in the context of cable operators?
  • In a DC series circuit with R1 = 150 ohms, R2 = 150 ohms, R3 = 550 ohms, and IT = 0.2 amperes, what is the voltage across R2?
  • Which activity is known to encourage creative thinking?
  • What is the effect of increased port-to-port isolation in a drop splitter?
  • What does "bypass AC current capacity" refer to in a line extender amplifier?
  • What should be done to fix signal leakage from a drop splitter?
  • Which of the following can cause variations in signal levels during transmission?
  • Which method can be used to help resolve a problem while applying the six-step troubleshooting process?
  • What occurs in a magnetic material when only some magnetic domains are aligned?
  • Elements known as conductors typically have what characteristic?
  • What typically causes excessive current flow in an electrical circuit?
  • Given a measured input level of 9 dBmV and an insertion loss of 3.5 dB, what is the theoretical output level at 197 MHz?
  • In audio engineering, the decibel scale is often used to measure?
  • What is the best approach to speaking with a customer?
  • What does the term "must-carry" refer to in relation to cable operators?
  • What would the output power be if the input power ratio is 2:1?
  • In the equation E = IR, what is the formula to find I?
  • What is the function of a permanent-magnet loudspeaker's cone?
  • What is the result of -49 divided by -7?
  • What is the sum of (75 x 10^3) + (25 x 10^4)?
  • What is the role of the power source in an electrical circuit?
  • What is a potential downside of local franchises compared to state-issued franchises for cable services?
  • What should be done at a drop splitter to check for ingress?
  • What type of antenna is required by the FCC for measuring signal leakage?
  • How many kilowatt-hours (kWh) would a standby power supply providing 60 volts and 10 amperes for 3.5 hours supply?
  • In troubleshooting, how do hard skills compare to soft skills?
  • What is the square root of 81?
  • Which component in the circuit provides a path for current flow?
  • Which of the following describes the relationship between voltage and resistance in a DC series circuit?
  • In what year did the FCC enact additional rules for closed captioning of programming delivered via Internet protocol?
  • In a loop-through system, which cable comes from the outside wall?
  • What is the result of the expression (20) / (-4) + (-2) x (-10) - (-2) x (7)?
  • What is true regarding the current flow in a DC series circuit?
  • How is load resistance defined in an electrical circuit?
  • What is the difference of (-62) and (20)?
  • What is the relationship between VHF and UHF leakage and ingress?
  • Which connector type utilizes a bayonet coupling mechanism?
  • In the expression 6 x -3 + 12, what is the outcome?
  • What is the recommended method for closing a distribution amplifier housing?
  • What is an effective method for controlling expectations?
  • Which of the following are the aeronautical frequency bands?
  • What is the result of the expression (-25) + (42) + (-62) + (20)?
  • Why is proper shielding important in electronic equipment?
  • What is the total of (-2) + (-2) + (10)?
  • What is the total DC loop resistance of a 1,850-foot piece of 0.500-inch coaxial cable with a resistance of 1.34 ohms per 1,000 feet?
  • What is ingress in the context of cable systems?
  • Why is a leakage detector preferable to a signal level meter (SLM) for detecting leakage?
  • What percentage is equivalent to a ratio of 1:5?
  • How does the magnetic field created by a straight piece of wire compare to that of a looped wire?
  • What does the load in an electrical circuit do?
  • What event coincided with the growth of cable TV services in metropolitan areas?
  • What does locating a reflective event using an optical time domain reflectometer (OTDR) indicate?
  • What is the primary method for creating an electromagnet?
  • Where should an ohmmeter be connected to measure resistance?
  • How can the proper operation of a leakage detector in a monitoring vehicle be verified?
  • Which of the following units can be used to represent signal level values?
  • What type of cable would typically exhibit a power loss of 10 dB?
  • What is the maximum tap value that can be installed with a line extender output of 45 dBmV @ 745.25 MHz?
  • What is a block diagram in circuit graphics?
  • Which behavior represents a characteristic of a good listener?
  • Which type of wiring is used to connect speakers to an audio source?
  • How was magnetism first discovered?
  • What is an advantage of fiber-optic pigtail splicing?
  • What is one-tenth bel or 1 dB fundamentally defined as?
  • What is the result of the expression (-17) - (-34)?
  • What are symptoms of poor attitude behavior associated with stress overload?
  • According to the FCC, what is the maximum acceptable field strength for leakage at 30 meters for certain frequencies?
  • To convert a fraction to a percent, you should?
  • What is the function of the plug-in connectors in a line extender amplifier housing?
  • What does the term voltage refer to in electrical terms?
  • What technology will enhance the importance of controlling leakage and ingress issues?
  • What prevents electrons from breaking away from the nucleus due to centrifugal force?
  • Which statement is true about 110-type punch-down blocks?
  • What is the result of the expression (75 x 10^3) + (2.5 x 10^4)?
  • Why should phrases like "You didn't" be avoided during customer conversations?
  • What does an increase in workload for forward error correction (FEC) indicate?
  • What are the letter and symbol designations for current?
  • Which metric prefix corresponds to 10 to the power of -3?
  • A coaxial cable with an attenuation of 10 dB will experience what percentage of the input signal remaining?
  • What is the total DC loop resistance of a 350-foot piece of Series 59 drop cable at 56.04 ohms per 1,000 feet?
  • Which organization is responsible for the implementation of closed captioning rules for programming?
  • What do optical splitters do in the forward direction?
  • What approach is best for helping a customer feel valued during a conversation?
  • What is a primary use of the bel and decibel units?
  • What type of current flows in one direction and is typically used in battery-powered devices?
  • What is the product of (17) x (-19)?
  • How much signal is needed from the subscriber's tap port @ 750 MHz to provide a minimum of +3.0 dBmV to each TV set when using a two-way splitter?
  • What would indicate a need for corrective measures at a customer's tap?
  • What happens to current flow if there is a failure within a circuit component?
  • Which formula is used to calculate normal attenuation of coaxial drop cable?
  • If a circuit has a voltage of 12 volts and a current of 2 amperes, what is the resistance?
  • Who is primarily responsible for the majority of ingress issues in a system?
  • How many input and output ports are typically found in most line extender housings?
  • What are the three basic elements of an electrical circuit?
  • Which metal is known to have the greatest conductance?
  • Which type of information must be included with the annual reporting to the FCC regarding signal leakage?
  • What colors are typically used on a telephone station jack?
  • What step in the troubleshooting process involves asking the customer questions about recent contractor work?
  • What factor determines the strength of an electromagnetic field?
  • What results in a normal current flow in a circuit?
  • What effect does excessive current have on a conductor's insulating cover?
  • What year marked the replacement of the Emergency Broadcast System (EBS) with the Emergency Alert System (EAS)?
  • To provide a minimum of 3.0 dBmV to the TV set from the subscriber's tap port @ 750 MHz, how much signal is necessary if the drop is 150 feet of Series 6 cable?
  • What does the term "bel" relate to in the context of telecommunications?
  • What is equivalent to 0 decibel millivolt (dBmV)?
  • Which feature of the signal level meter (SLM) is particularly useful?
  • What current would an applied voltage of 60 volts cause in a circuit with a resistance of 300 ohms?
  • According to the FCC, leaks at what level and above must be logged and repaired?
  • What is an attenuation pad?
  • How much power (in watts) is consumed in a circuit with an applied voltage of 60 volts and a load of 150 ohms?
  • Which category of wiring is designed to minimize Near-End Crosstalk and attenuation?
  • What is the role of a return amplifier?
  • Which frequency is specifically allocated for public safety communications?
  • The term "attenuation" in coaxial cables refers to?
Subscribe

Get the latest from Examzify

You can unsubscribe at any time. Read our privacy policy